June 7th, 2009 by admin

Why your next pickup should be a GM
Oddly enough, out of all of the research done into hybrid technology GM has been forward thinking enough to make theirs are not only affordable, but ingenious as well. They now offer both the Sierra and the Silverado pickups as hybrids country wide. Using a technology not formerly seen in hybrids, GM attempted to not only lower emissions in their pickups, but to make them handier as well. Affordable technologyGM wanted to make a hybrid truck that was too well priced to turn down, the major complaint of the hybrid models is high price tag which counteracts the gas mileage benefits. In response to this GM produced their pick up hybrids to cost only $1500.00-$2500.00 more than its gas guzzling brothers, saved with tax cuts at the pump within the first few years of ownership. Especially if you consider that the hybrids produce a 10% improvement in fuel economy, all without sacrificing any power. Both the Sierra and Silverado offer the same 245 horsepower V8 engine, and can tow up to 7,700 pounds. If you consider that pickup truck drivers are not sacrificing any power and when sitting stopped in traffic it emits very limited pollution for their size. Hybrid systemGM employs what they call a “flywheel alternator starter hybrid system” which uses a compact electric motor incorporated between the engine and the transmission. This electric engine runs the truck when it is slowing or idling at a standstill. They calibrate the flywheel alternator system to turn off the engine more frequently than even those systems used in most smaller hybrid models. Eliminating much of the pollution caused by slow moving traffic in high volume. Now your work truck can double as a generatorBoth the Sierra and the Silverado boost four 120-volt, 20 amp three-prong outlets which can be used to provide power for electrical tools and electronics. This eliminates any need for a gassy generator spewing fumes into the air at a work site. The truck must be running, but utilizing it’s electric engine allows it to run virtually emission free. GM reports that their hybrid trucks can continue to pump out power for up to 32 hours non-stop before needing to refuel. Aimed specifically at contractors, whose need to access abundant sources of energy and drive long miles to job sites fuel this intelligent new take on a work truck. Testers reportThe power source for tools was not quite as juicy as GM would have you think, however the idea is a brilliant one. No doubt in a few generations they will have nailed down this imperfection in an already forward thinking vehicle. Although the gas mileage is a tad better overall, it borders on insignificant. Which again is certain to be addressed and updated in generations to come. Reviewers say that the feel of the engine cutting out as you hit ten miles an hour is a bit disconcerting, and takes some getting used to, but its pollution saving benefits far outweigh that small detail. Every accessory on the truck is electrical, so the gas engine only runs when it is needed to for its sole purpose, to accelerate the vehicle. Overall appealThe brilliance behind the ideas developed for these pickup truck models is really what drives them at this point. Fine tuning is necessary of any piece of equipment and GM has been making pick up trucks for a long time. They will continue to address the issues and refine the existing good points, driving the hybrid market to continue to bring us new and innovative ideas. <b>About the Author:</b> My name is Paige Filler and I'm a creative writer with a love of all things that go vroom. I do my homework to bring thought and innovation into everything I write about the auto industry. You can find more of my stuff at <a href="http://www.cash4usedcars.com/" target="blank">Cash 4 Used Cars</a>, and <a href="http://blog.cash4usedcars.com/" target="blank"> this blog.</a>
Source: www.ArticlePros.com

How To Dispose Of Your Old ATV Tires
When it comes time to replace your old and worn ATV tires, many riders are eager to purchase new tires, but many are unaware what to do with the old ones. Regardless where you live, throwing old tires in a body or water or natural environment is improper?and in many cases illegal?since the tires can corrupt nature. When disposing of your old ATV tires, be sure to do so in a proper and legal manner that will not negatively impact the environment for future generations. More and more often, tires are being recycled and formed into all sorts of new products. From park benches to carpets, recycled rubber is a durable and economical product. When you are faced with the decision what to do with your old ATV tires, look to your local recycling company to see if rubber is accepted. Although you may not be able to place your tires to the curb if you community is involved with curbside recycling, the recycling plant may be able to take the tires off your hands. Look to the phonebook or internet to find a recycling facility near you and make a quick visit or telephone call to see if your tires are able to be recycled. Most tire stores that provide you with new tires for your ATV will be able to take your old ones. Before you make the change, be sure to ask the tire center what they do with old tires if you are concerned about the environmental impact unused rubber causes. Also, there may be a slight fee involved with properly disposing of your old tires, so know this amount upfront in order to prevent any surprises at the cash register. The state in which you live may have certain regulations or fees involving tire disposal, and this is often incorporated into your bill and is listed separately from the cost of the new tires or the labor to install the tires on your ATV. If your old tires still have life in them, consider giving them to a friend or family member with an ATV. Keep in mind that old tires should only be used if they still have ample tread and are able to ensure the vehicle can be driven safely. Also, consider selling your old ATV tires so that you can use the profits to buy a new set. Look to your local newspaper and list a classified advertisement or turn to the internet with sites like Ebay or Craigslist to sell your tires. These are great resources and you may even find a new set of ATV tires listed at a more economical price than offered at your local tire store. Bill Carmel works with <a href="http://www.u-atv-tires.com">ATVs</a>
Source: www.ArticlePros.com

Installing Aftermarket Head Units
Are you thinking about installing your own car stereo head unit? Be sure to read this article and figure out what you will need to do to get it done. Upgrading the sound system is usually one of the first modifications attempted when we talk about car customization. The best place to start is with a good head unit. If you plan to install it yourself, read on for some technical tips from our experience installers. You will need a few tools to do the job right, so start by collecting some screwdrivers (flat head and phillips head), a socket set, wire cutters, wire splitters, butt connectors or heat shrinking sleeves, electrical tape, zip ties, solder and a soldering iron, and some patience. The first thing I would do before installing I would suggest buying the stereo wiring harness for your vehicle application. This will make the installation easier for you if you are a beginner, and it allows for easier replacement of the stock radio (if you choose to sell the vehicle in the future) and swapping or upgrading to a different aftermarket head unit. Begin by disconnecting the negative battery cable from the battery. This will ensure that you don’t accidentally cross any wires and burn out a new piece of equipment. Next, remove the old head unit. If you need to see how this is done on your specific vehicle, you can look up your vehicles application on installdr.com. This is a great resource for seeing pictures of how to remove the head unit. Once it is loose, disconnect the wiring harness and the antenna from the head unit and remove it completely. There are two types of wiring harnesses you can get. There is the universal wiring harness that connects to your vehicles existing wiring harness, and has the unfinished wire ends that connect to the color coded wires of your new head unit. There is also a wiring harness that has a harness on both ends, and just clicks in place on both sides. These are the easiest to install, but can be harder ot find to match your vehicle to the head unit. Most wiring harnesses are the universal type, so we will focus on those. If you have obtained the wiring harness, you will notice the color coded wires in the back of the head unit. The wires on the head unit and wiring harness should match. The head unit wires and the wiring harness wires will be partially spliced for easy installation. There are several good ways to connect the wires. One way is to use butt connectors, which crimp the wires within a connector. These can be picked up almost anywhere that sells/installs head units, or at Walmart, etc. My favorite way requires a soldering iron and heat shrinking sleeves. Twist the wires together tightly. Apply just enough solder to weld the two wires together. Now fold them over parallel to one of the wires. Slide the sleeve over the connection and heat it with a heat gun or good hair dryer. I have had to rewire or repair systems where butt connectors were used, but this could be installer error, and not a problem with the connectors themselves. I have never had any of the soldered connections fail. Once all the connections are made, and the sleeves heated and shrunk in place, I like to take a zip tie and tie them all together. Clip the excess zip tie for a clean finished look. Connect the wiring harness of the head unit to the wiring harness connected to the vehicle. Plug in the antenna (you may find you need an antenna adapter in some applications). Now slide the head unit in place, but don’t attach it yet. Reconnect the negative battery cable and turn on the head unit (make sure the key is turned to the ACC position). It should be functioning properly at this point. If you plan on adding an amp, or have purchased one for this setup, turn the unit off and connect the RCA cables. Run them through the dash to the floorboard and to the amp (more on how to successfully do this in future articles). If you encounter problems, you can email <A HREF="mailto:support@majesticmodifications.com">support@majesticmodifications.com</A> for help. Brought to you by <A HREF="http://www.majesticmodifications.com" TARGET="_blank">http://www.majesticmodifications.com</A>. Majestic Modifications is your online source for auto parts and accessories, installations advice and technical support.
Source: www.ArticlePros.com